Pubblica i tuoi prodotti
MVB Modulating Vertical Hydronic Boilers 503A-2003A
Raypak

MVB Modulating Vertical Hydronic Boilers 503A-2003A

Time-honored technologies unite with cutting-edge advancements in Raypak’s MVB modulating vertical boiler. Small space is no longer a problem, and our compact design fits through a 32” door opening to make it the perfect choice for those hard-to-reach retrofit projects.

Features

  • 86.2% Thermal Efficiency at Full Rate; Up to 88.4% at Part Load.
  • Positive vent pressure, Condensing Appliance.  Cat IV Vent Required.
  • Cast-Iron Headers with Copper Finned-Tube Heat Exchanger standard. Brass Headers and Cupro-Nickel tubes available as options. ASME Section IV constructed and stamped, National Board registered.
  • CSA Low-Lead certified, less than 0.25% Lead.
  • Certified to ANSI Z21.13.
  • Minimum Inlet Water Temperature: 120°F.
  • Maximum Operable Outlet Water Temperature: 235°F.
  • Electronic Modulation, up to 7:1 Turndown.
  • VERSA IC® Control Package with Built-In Outdoor Reset Function and LCD Display, Including System Sensor, Indirect Sensor & Indirect Supply Sensor.
  • Status Display Lights.
  • Cascade control of up to 8 units, no external sequencer required.
  • Cascade in parallel or sequential modulation modes.
  • Diagnostics Center with History, English, no codes.
  • Modbus RTU BMS port (RS485).
  • 0-10 VDC BMS Interface (Setpoint or Direct Drive).
  • All models indoor/outdoor construction.
  • Certified under SCAQMD Rule 1146.2.  Meets all Low NOx regulations.
  • Engineered with precisely matched system components.
  • Smallest installed footprint (5.4 square feet) design fits tight spaces and easily replaces larger boilers.
  • 100% Factory Fire Tested.
  • Complete cabinet protects all controls and wiring. Tough, rust-resistant powder-coat finish.
  • Suitable for altitudes up to 10,000 ft. (derate above 2,000 ft.).
  • No boiler condensate drain required (proprietary design)
  • Available for natural gas or propane.
  • Integral Combustion Air Filter (MERV8).
  • Multiple Pump Outputs – Boiler Pump, System Pump, Indirect Pump.
  • Whisper-Quiet Operation.
  • Proudly Assembled in the USA.

Options:

  • Outdoor air Sensor (B-32)
  • BACNet IP, BACnet MS/TP, Modbus TCP, N2 Metasys (B-85)
  • Lonworks (B-86)
  • Alarm with 4” Bell (E-5)
  • Low Water Cutoff (F-10)
  • Cold Water Start (not for potable water systems)
  • Cold Water Run
  • Condensate Neutralizer (Z-12)
Voce di capitolato
    • 86.2% Thermal efficiency at full rate 
    • 100% Factory fire-tested 
    • VERSA IC® Integrated controller with 7" color touchscreen display 
    • Raymote™ remote connectivity provided standard 
    • Electronic modulation, constant ratio 7:1 turndown 
    • Full safety diagnostics with history 
    • Status display lights 
    • Cascade up to 8 boilers - no external sequencer required 
    • Cascade in parallel or sequential modulation modes 
    • Modbus RTU BMS Port 
    • Maximum outlet water temperature: 235°F (113°F) 
    • Minimum acceptable inlet water temperature: 120°F (49°F) 
    • Limited 20-year thermal shock warranty 
    • Limited 10-year heat exchanger warranty 
    • SCAQMD Rule 1146.2 certified, Low NOx < 20 ppm 
    • Proudly Assembled in the USA
Specifiche tecniche
  • Rif. UnicoMVB-Modulating-Vertical-Hydronic-Boilers-503A-2003A
  • Famiglia di prodottoBoilers & Water Heaters
  • Gruppo di famigliaHydronic Boilers
  • TipoOggetto (oggetto singolo)
  • Data di pubblicazione2020-10-01
  • Numero di versione1
Relativo a
  • Progettato inStati Uniti
  • Prodotto inStati Uniti
Classificazioni
  • Categoria BIMobjectRiscaldamento, ventilazione e condizionamento - Caldaie
  • Clasificazione IFCCaldaia
  • Codice ETIMEG015210
  • Nome ETIMBoilers and heaters
  • Nome UNSPSCBoilers
  • Codice UNSPSC401020
  • Codice Uniclass 2015Pr_60_60_08
  • Descrizione Uniclass 2015Boilers
  • Codice CSI MasterFormat 201423 52 00
  • Titolo CSI MasterFormat 2014Heating Boilers
  • Numero OmniClass23-33 11 00
  • Titolo OmniClassCommercial Boilers
  • Codice CSI UniFormat IID3090
  • Titolo CSI UniFormat IIOther HVAC Systems & Equipment

Disponibilità Regionale

Nord America
Canada
Stati Uniti
Common.Footer.ValueProp.Image.AltText

App di progettazione per Revit

Carica le famiglie direttamente nel tuo modello Revit con un solo clic

Ottieni un posto per accedere più facilmente a nuovi oggetti, archivia le tue famiglie Revit e collabora con il tuo team.

  • Segno di spuntaLavora direttamente con gli oggetti BIM accanto a Revit
  • Segno di spunta 2 GB di spazio di archiviazione cloud: archivia i tuoi contenuti Revit
  • Segno di spunta Ottieni l'LCA (A1-A3) del carbonio incorporato direttamente da Revit