Rail and Disconnect Systems

Rail and Disconnect Systems

Features and Benefits

  • Simplifies the installation and removal of a submersible pump from a basin.
  • Economical – reduces time and cost of removing pump from basins less than 8′ (2 m) deep
  • Safety – keeps personnel out of pits and out of contact with contaminants
  • Inspections made fast and easy

Z-RAIL® DISCONNECT SYSTEMS (1-1/4″ to 3″ vertical discharge):

  • Used with threaded vertical discharge pumps
  • Ductile iron stationary disconnect, rail plate and guide and upper rail support
  • 304 stainless steel hardware
  • Positively seated with a Buna-N seal ring
  • 3/4″ guide rails (not included) direct the pump to its proper seating location
  • Non-sparking design for Class I Division 1 Group C & D locations
  • Intermediate stabilizer bracket recommended for basins greater than 12′ (3.6 m) deep

P/N 10-0789 lifting bails are required on 6160, 6180, 6280, 6290, 7010 and 7020/7021 models to balance pump and rail plate evenly. Other models already include proper lifting device. Stainless steel lifting cables available.

FLANGED RAIL SYSTEMS (2-1/2″ to 6″ horizontal discharge):

  • Used with flanged horizontal discharge pumps
  • An ANSI flange pattern for universal adaptability to most submersible pumps
  • Robust Class 30 cast iron construction
  • Powder coated epoxy protection
  • 304 stainless steel hardware and rail guides
  • Positively seated with a Buna-N seal ring
  • 2″ (5 cm) guide rails (not included) direct the pump to its proper seating location

1/4″ (6 mm) lifting cable not included. See ZM1328 for correct cable. One intermediate guide rail bracket is required for every 20′ (6 m) for 3″ (76 mm) system, or 15′ (5 m) for 4″ (102 mm) system, of basin depth.

3″, 4″, 6″ FLYGT GUIDE RAIL SYSTEM ADAPTERS

  • For retrofitting 3″, 4″ or 6″ horizontal discharge pumps to existing Flygt rail systems.
  • Cast iron construction
  • Flange conforms to ANSI B16.10 fully flat/MSS SP-6
  • For use with all 6400, 61 HD and 6700 series pumps with 3″, 4″ or 6″ discharges and 2″ NPT rail pipe
  • Flange gasket and stainless steel bolts included

DISCONNECT SYSTEMS

Reduces time and cost of removing a pump. Disconnect only (1-1/4″, 1-1/2″ and 2″ discharge).

  • Disconnect fitting used for shallow systems where guide rails are not necessary.
  • Pull rod not included.
Teknisk specifikation
  • Unik ref.rail-and-disconnect-systems
  • ProduktfamiljBasin and Accessories
  • ProduktgruppRail and Disconnect Systems
  • TypObjekt (enstaka objekt)
  • Publiceringsdatum2025-06-14
  • Edition nummer1
Relaterad
  • HuvudmaterialCast iron
  • Designad iUSA
  • Tillverkad iUSA
Klassificering
  • BIMobjektkategoriRörläggning - Pumpar
  • Uniclass 2015 kodPr_65_53_65
  • Uniclass 2015 beskrivningPump accessories
  • OmniClass nummer23-27 17 00
  • OmniClass TitelPumps

Region tillgänglighet

Nordamerika
Amerikanska Jungruöarna
Anguilla
Antigua och Barbuda
Aruba
Bahamas
Barbados
Belize
Bermuda
British Virgin Islands
Caymanöarna
Costa Rica
Curaçao
Dominica
Dominikanska republiken
El Salvador
Grenada
Grönland
Guadeloupe
Guatemala
Haiti
Honduras
Jamaica
Kanada
Karibiska Nederländerna
Kuba
Martinique
Mexiko
Montserrat
Nicaragua
Panama
Puerto Rico
Saint Christopher och Nevis
Saint Lucia
Saint Vincent och Grenadinerna
Saint-Barthélemy
Saint-Martin
Saint-Pierre-et-Miquelon
Sint Maarten
Trinidad och Tobago
Turks och Caicos Islands
USA