QF Tap In

Nordfab manufactures ducting for use in dust, mist, and fume collection systems.

Quick-Fit® Tap-Ins are standard with QF rolled ends, allowing quick connections with other QF® ductwork. Used to cut into existing duct lines to begin a new Quick-Fit (QF) section.

When ordering, specify material; gauge (if nonstandard); dimensions A (existing pipe diameter) and C; and end styles if not all QF.
Saddle length and width = 3" all directions from Branch Tube C
Available in galvanized steel and 304SS (as shown below) or optional 316SS or carbon steel
Available with flanged ends in diameters up to 72", and other various end types
Optional gauges 18, 16, 14, 12 and 10

Contact Nordfab or your local Nordfab dealer for assistance with optional end types, larger sizes, and material / gauge options.

Quick-Fit has been used in a wide variety of applications, wherever dust collection or fine particulate transfer is required. Quick-Fit saves time and money on installation, is easy to clean out, is adaptable to existing ductwork, and is easily re-used during shop floor reconfigurations. Learn more about why Quick-Fit may be the best solution for you.

Voce di capitolato

A. General Fabrication Requirements: Comply with SMACNA's "HVAC Duct Construction Standards - Metal and Flexible," Ch. 3, "Round, Oval, and Flexible Duct," based on indicated static-pressure class unless otherwise indicated.
1. Construct ducts of galvanized sheet steel unless otherwise indicated. 304SS Optional.
2. Basis-of-Design Product: Subject to compliance with requirements, provide Nordfab Ducting, LLC; Quick Fit (QF) Duct.
B. Connection Joints: Joint types are fabricated in accordance with SMACNA's "HVAC Duct Construction Standards - Metal and Flexible," for static-pressure class, applicable sealing requirements, materials involved, duct-support intervals, and other provisions in SMACNA's "HVAC Duct Construction Standards - Metal and Flexible."
1. Quick Fit Joints in Ducts 3 to 24 inches (76 to 510 mm) in diameter. Flange: Optional.
2. Flanged Joints in All Ducts Greater than 24 inches (610 mm) in diameter.
C. Longitudinal Seams: Seam types are fabricated in accordance with SMACNA's "HVAC Duct Construction Standards - Metal and Flexible," Figure 3-2, "Round Duct Longitudinal Seams," for static-pressure class, applicable sealing requirements, materials involved, duct-support intervals, and other provisions in SMACNA's "HVAC Duct Construction Standards - Metal and Flexible."
1. Fabricated round ducts 3 to 24 inches (76 to 510 mm) in diameter to have laser-welded or plasma-welded longitudinal seams.
2. Fabricated round ducts above 24 inches (610 mm) in diameter to have plasma-welded longitudinal seams.

Specifiche tecniche

Rif. Unicous-qf-tap-in
Famiglia di prodottoQuick-Fit Clamp Together Ducting
Gruppo di famigliaBranches
TipoOggetto (oggetto singolo)
Data di pubblicazione2024-05-08
Numero di versione1

Links

Link al Prodottohttps://www.nordfab.com/en-us/products/qf-ducting/branches/us-qf-tap-in
Descrizione Tecnicahttps://www.nordfab.com/-/media/files/nordfab/americas/americas-product-data-sheets/nordfab_tap_in.pdf

Relativo a

Materiale principaleAcciaio zincato
Materiale secondarioStainless steel 304
Progettato inStati Uniti
Prodotto inStati Uniti

Classificazioni

Categoria BIMobjectRiscaldamento, ventilazione e condizionamento - Raccolta della polvere
Clasificazione IFCRaccordo del condotto
Codice ETIMEG015540
Nome ETIMFittings, flanges and connectors
Codice Uniclass 2015Pr_65_65_25
Descrizione Uniclass 2015Ductwork and fittings
Codice CSI MasterFormat 201423 31 13.19
Titolo CSI MasterFormat 2014Metal Duct Fittings
Numero OmniClass23-33 49 00
Titolo OmniClassHVAC Ductwork