Termékek közzététele
Rail and Disconnect Systems
Zoeller Company

Rail and Disconnect Systems

Features and Benefits

  • Simplifies the installation and removal of a submersible pump from a basin.
  • Economical – reduces time and cost of removing pump from basins less than 8′ (2 m) deep
  • Safety – keeps personnel out of pits and out of contact with contaminants
  • Inspections made fast and easy

Z-RAIL® DISCONNECT SYSTEMS (1-1/4″ to 3″ vertical discharge):

  • Used with threaded vertical discharge pumps
  • Ductile iron stationary disconnect, rail plate and guide and upper rail support
  • 304 stainless steel hardware
  • Positively seated with a Buna-N seal ring
  • 3/4″ guide rails (not included) direct the pump to its proper seating location
  • Non-sparking design for Class I Division 1 Group C & D locations
  • Intermediate stabilizer bracket recommended for basins greater than 12′ (3.6 m) deep

P/N 10-0789 lifting bails are required on 6160, 6180, 6280, 6290, 7010 and 7020/7021 models to balance pump and rail plate evenly. Other models already include proper lifting device. Stainless steel lifting cables available.

FLANGED RAIL SYSTEMS (2-1/2″ to 6″ horizontal discharge):

  • Used with flanged horizontal discharge pumps
  • An ANSI flange pattern for universal adaptability to most submersible pumps
  • Robust Class 30 cast iron construction
  • Powder coated epoxy protection
  • 304 stainless steel hardware and rail guides
  • Positively seated with a Buna-N seal ring
  • 2″ (5 cm) guide rails (not included) direct the pump to its proper seating location

1/4″ (6 mm) lifting cable not included. See ZM1328 for correct cable. One intermediate guide rail bracket is required for every 20′ (6 m) for 3″ (76 mm) system, or 15′ (5 m) for 4″ (102 mm) system, of basin depth.

3″, 4″, 6″ FLYGT GUIDE RAIL SYSTEM ADAPTERS

  • For retrofitting 3″, 4″ or 6″ horizontal discharge pumps to existing Flygt rail systems.
  • Cast iron construction
  • Flange conforms to ANSI B16.10 fully flat/MSS SP-6
  • For use with all 6400, 61 HD and 6700 series pumps with 3″, 4″ or 6″ discharges and 2″ NPT rail pipe
  • Flange gasket and stainless steel bolts included

DISCONNECT SYSTEMS

Reduces time and cost of removing a pump. Disconnect only (1-1/4″, 1-1/2″ and 2″ discharge).

  • Disconnect fitting used for shallow systems where guide rails are not necessary.
  • Pull rod not included.
Műszaki specifikáció
  • Egyedi azonosítórail-and-disconnect-systems
  • TermékcsaládBasin and Accessories
  • TermékcsoportRail and Disconnect Systems
  • TípusObjektum (egy termék)
  • Megjelenés dátuma2025-06-14
  • Verziószám1
Kapcsolódó adatok
  • Elsődleges anyagÖntöttvas
  • Tervezés helyeEgyesült Államok
  • Gyártás helyeEgyesült Államok
Besorolások
  • BIMobject kategóriaVízvezeték-szerelés - Pumpák
  • Uniclass 2015 kódPr_65_53_65
  • Uniclass 2015 leírásPump accessories
  • OmniClass szám23-27 17 00
  • OmniClass névPumps

Termék elérhetősége

Észak-Amerika
Anguilla
Antigua és Barbuda
Aruba
Bahama-szigetek
Barbados
Belize
Bermuda
Brit Virgin-szigetek
Caribbean Netherlands
Costa Rica
Curaçao
Dominikai Közösség
Dominikai Köztársaság
Egyesült Államok
El Salvador
Grenada
Grönland
Guadeloupe
Guatemala
Haiti
Honduras
Jamaica
Kajmán-szigetek
Kanada
Kuba
Martinique
Mexikó
Montserrat
Nicaragua
Panamaváros
Puerto Rico
Saint Kitts és Nevis
Saint Lucia
Saint Pierre és Miquelon
Saint Vincent és a Grenadine-szigetek
Saint-Barthélemy
Saint-Martin
Sint Maarten
Trinidad és Tobago
Turks- és Caicos-szigetek
Virgin-szigetek